Archive for January, 2011

Xfce 4.8 comes to Xubuntu Natty

25, January 2011

Xfce 4.8 released, see www.xfce.org

Xfce 4.8 seems to be fully implemented in Xubuntu Natty 11.04 now, I’ve been running Xubuntu since Alpha 1 having decided I don’t want either Unity, it’s fallback Gnome or Gnome shell and am loving it. I’m running it on my laptop as the main o/s doing safe upgrades every few days and [fingers crossed] not had any problems. I think Xubuntu is going to be my new main o/s and am looking forward to Alpha 2 in February when I’ll be testing it on my spare “testing” PC .

Advertisements

Natty Unity

5, January 2011

So I’ve been doing some ISO testing of the Natty Alpha 1 release and have had one or two problems [see previous post iso Testing Natty ] but my main problem with it has been the decision to replace the default Gnome desktop with Unity. Unity is a 3D replacement for the 2D Gnome desktop which Gnome are about to replace anyway with Gnome Shell. Ubuntu seem to have decided Gnome Shell is not the direction they want to go so are replacing the desktop with their own. Unity brings the notebook and desktop versions of Ubuntu together with only minor differences which will be detected and applied during install. The standard approach will therefore be a notebook type display on both desktop and notebook. The main difference will be the loss of the bottom panel, the replacement of the top panel with a more interactive menu and a Mac style icon dock down the left hand side.

When you install the Ubuntu default now you will need a 3D enabled graphics card to run Unity or you will be presented with a pop up message currently;

Information:
Sorry you don’t have 3D support, install it for
your graphic hardware to get Unity or please
reboot and select “Classic session” at startup.

Not a very helpful message in my opinion, basically you can go into [System], [Administration], [Login Screen] and change [Ubuntu desktop Edition] to [Ubuntu Classic Desktop] then log out and back in again to 2D Classic Mode but this is not obvious from the message. The other option would be to add the 3D driver [if your card supports 3D] and log out and back in again for Unity to display, Nvidia owners beware! The message is particularly unhelpful if you are running a Live CD version or USB stick with persistence not enabled because you will not be able to install the driver as a restart will wipe the changes, noobs will be confused.

Personally I don’t like Unity, it’s more Mac like styling, I don’t have 3D effects turned on and don’t want them, the dock on the left is unnecessary clutter but if I wanted one there are plenty of docks available without this being the default. We are told we can use the Classic 2D Gnome desktop if we don’t like Unity but that this will eventually disappear when Gnome Shell arrives and Gnome 2 is depreciated. My thoughts for Gnome Shell are much the same I just don’t want to go there so the hunt starts for an alternative. I’ve already tested Lubuntu with it’s LXDE desktop and although I like the styling it’s still a bit basic. So for now Xubuntu with it’s Xfce desktop is becoming my test o/s. I’m currently running Natty Xubuntu testing and loving it.

Sheevaplug

2, January 2011

Ok so I’ve had my Sheevaplug since January 2009 and have now bricked it at least 3 times trying to be too clever by half! As it’s getting to be a rugular thing and it always takes me hours to work out what to do, here are my instructions.

I have used the same info. from the page below and added/changed it to reflect my process, please read both to make sure you understand what you are doing! as I take no reponsibility for errors blah, blah etc.etc.

I found the “instructions”, script & packages on this site

SheevaPlug Installer Page;

http://plugcomputer.org/plugwiki/index.php/SheevaPlug_Installer

but to be honest they are a bit difficult to follow for a bit of a noob so I’ve adapted them a bit.

The installer will reflash a bricked plug & can be used to install another distro [I’ve used Debian Squeeze this time] but if you just want it back to “factory settings” use the packages as they are.

My plug is the BFLS one supplied with Ubuntu Jaunty on the internal flash card and the PC I will use to reflash it has Ubuntu Jaunty on it so although the scipt includes Windows support I won’t mention it here, see the above page for details.

Note::
The runme.php would not run on Ubuntu 10.10 as the version of python on Ubuntu 10.10 has depreciated some terms. I got round this at the time by installing the old 32 bit Karmic Ubuntu and using that but since then I have found the possible answers in this post

http://plugapps.com/forum/viewtopic.php?f=20&t=428#p3178

but not tested the solution yet although I have saved copies of the files it talks about for future use, contact me if you need them.

If you can get onto the plug then backup your stuff as this script will delete the lot, be Warned

First Download the tarball from

http://www.plugcomputer.org/index.php/us/resources/downloads?func=select&id=5

This includes all the files you need to re flash your sheevaplug with the default install of Ubuntu Jaunty. Check out this post http://plugcomputer.org/plugforum/index.php?topic=878.0 if you want to Install a Debian system, you can either download the pre-built Lenny or Squeeze rootfs.tar.gz files or use the script that mgillespie has created.

You now need to add the following packages to your host PC, cu, php5-cli, and libftdi1, so install with the following commands in a [Terminal];

$ sudo apt-get install cu

$ sudo apt-get install php5-cli

and

$ sudo apt-get install libftdi1

adding libftdi1 fixes the error message “openocd/openocd: error while loading shared libraries: libftdi.so.1: cannot open shared object file: No such file or directory” latter on.

You now connect the Sheevaplug to your PC with the USB lead [supplied] and issue this command in a [Terminal];

$ cu -s 115200 -l /dev/ttyUSB1

Note: [you may need to try cu -s 115200 -l /dev/ttyUSB0 my plug seemed to use either!]

If you get any sort of error message along the lines of

cu: open (/dev/ttyUSB1): No such file or directory
cu: /dev/ttyUSB1: Line in use

you need to issue the following commands in a [Terminal] to remove then add the driver support and re try.

$ sudo rmmod ftdi_sio

followed by

$ sudo modprobe ftdi_sio vendor=0x9e88 product=0x9e8f

If you now get on then you can proceed to the task at hand, if not it’s time to Google!. However I found that I could not get onto the plug sometimes and then realised that the plug end connection of the usb PC to plug cable was working itself out socket in the plug.

Installation

1. Prepare an empty USB stick that is FAT16/32 formatted. [Note: the 2 USB sticks I used were not detected by the plug even though I had used 1 of then before to unbrick my plug, be warned]. Re formatting and unplugging safely etc.etc did not help.

2. Extract the tarball you downloaded earlier into a folder on your PC (for example: ~/plug)

3. Edit the ~/plug/uboot/uboot-env/uboot-mmc-custom.txt or uboot-nand-custom.txt file to the correct MAC address according to the MAC address on the back of the Plug (default set to ethaddr 00:50:43:01:c1:e6). If your system is to boot from the internal flash then it’s the nand file you change, if it boots from a flash card in the side slot it’s the mmc file you change.

4. Copy all the files from ~/plug/installer to the USB stick.
NOTE: that the files should be written to the root directory of the USB stick. For example:

$ sudo cp -a ~/plug/installer/* /media/usb-pen/

5. You should now have a copy of the following;

  1. Init ramdisk (initrd)
  2. Kernel modules (modules.tar.gz)
  3. README.txt
  4. Root file-system (rootfs.tar.gz) Note if you are installing Debian, replace this file with the Debian version you have either downloaded or created with the mgillespie’s script.
  5. ubuntu-sheevaplug.sh
  6. Kernel (uImage)

6. Copy the uboot image (named uboot.bin) to the ~/plug/uboot/ directory, if it’s not there, mine was.

7. Safely remove the USB stick from the host PC, power off the plug and plug the USB stick into the Plug’s USB host interface (not via a USB HUB I disconnected all other periferals also!)

8. Connect the Plug to your PC with it’s USB cable.

9. On your PC in a [Terminal] again change to the working directory

$ cd ~/plug

and run the runme.php file with the command;

sudo php runme.php and either nand or mmc, nand if your system is on the internal flash mmc if on an external card, in my case;

$ sudo php runme.php nand

If you get an error message along these lines of;

Error: unable to open ftdi device: device not found
Runtime error, file “command.c”, line 469:
****    openocd FAILED
****    Is the mini USB cable connected?
****    Try powering down, then replugging the Sheevaplug

then try issuing these commands in a [Terminal] to delete and reload the driver, then retry;

$ sudo rmmod ftdi_sio
$ sudo modprobe ftdi_sio vendor=0x9e88 product=0x9e8f

[and make sure the USB cable at the plug end is firmly in]

If all goes well the process should start and end a couple of minutes later with a “beep” to indicate that the uboot install process has finished with the following message. [no beep on my plug]

****   U-boot should be up and running now. Open your console …

Now, open another Terminal  and log with this command

$ cu -s 115200 -l /dev/ttyUSB1

if you get this message;

## Booting image at 00800000 …
Bad Magic Number

as I did when using the first USB stick, then the process probably has not found the USB Stick and not loaded the o/s. You could try running the command;

run recover1

but in my case it just did not like the USB stick and I had to use another

If all goes well you should now see the o/s being installed with the final lines being..

* Starting kernel log daemon…
Ubuntu 9.04 ubuntu ttyS0

ubuntu login:                                                          [ OK ]
* Starting OpenBSD Secure Shell server sshd         [ OK ]
* Starting periodic command scheduler crond        [ OK ]
* Restarting OpenBSD Secure Shell server sshd     [ OK ]

with just an unhelpful flashing curser, in the centre of the last line!

After pressing [Enter] you get:

Ubuntu 9.04 ubuntu ttyS0

ubuntu login:

Just login with the default user root and password nosoup4u

done!!